Zelfbouw Links

Sluiten 136 kHz Projekten

Sluiten 472 kHz Projekten

Sluiten 500 kHz Projekten

Sluiten Multiband HF Projekten

Sluiten 160m Projekten

Sluiten 80m Projekten

Sluiten 60m Projekten

Sluiten 40m Projekten

Sluiten 30m Projekten

Sluiten 20m Projekten

Sluiten 17m Projekten

Sluiten 15m Projekten

Sluiten 12m Projekten

Sluiten 10m Projekten

Sluiten 6m Projekten

Sluiten 4m Projekten

Sluiten VHF Luchtvaart

Sluiten 2m Projekten

Sluiten 70cm Projekten

Sluiten 23cm Projekten

Sluiten 13cm Projekten

Sluiten 9cm Projekten

Sluiten 6cm Projekten

Sluiten 3cm Projekten

Sluiten 1,25cm Projekten

Sluiten EHF Projekten

Sluiten Antenne-aanpassingen

Sluiten Shack Accessoires

Sluiten Voedingen

Sluiten Meetinstrumenten

Sluiten µController Arduino

Junk Box Circuits

Sluiten Buizen

Sluiten Transistors BC-Serie

Sluiten Transistors BD-Serie

Sluiten Transistors BF-Serie

Sluiten IC 74XX-Serie

Sluiten IC 74LSXX-Serie

Sluiten IC 74SXX-Serie

Sluiten IC LM-Serie

Sluiten IC TDA-Serie

HF Propagatie
Bezoekers

   Bezoekers

   Bezoekers online

Zoeken




Antenne-aanpassingen - Dummy Loads

Klik voor vergroting400 Watt Oil-Filled Dummy Load by N4SPP
A dummy load is just one of those standard tools that you need in the shack. It's a load that has a purely resistive impedance of 50 ohms at all frequencies of interest (HF in my case). You don't need to pollute the airwaves while just tuning or testing your transmitter!
https://www.nonstopsystems.com/radio/frank_radio_antenna_dummy.htm

Klik voor vergrotingBuilding A RF Dummy Load by VO1PWF
If your doing any home brewing gear for ham radio its a great idea to have a dummy load. This will to your radio be the perfect antenna...it will never radiate but your radio sees a perfect 50 Ohm impedance.
http://www.linuxwolfpack.com/dummyload-homebrew.php

Build a simple HF/VHF 100W dummy load by G4AKE
Every radio amateur should own a dummy load. The one described here is capable of dissipating 100 Watts for short periods of time and provides a low power 50Ω port suitable for connecting a receiver or spectrum analyser for station monitoring.
http://www.derbywirelessclub.org.uk/dummy_load.pdf

Klik voor vergrotingDummy-Load met 50 Ω chip door PAŘFRI
Het zelf maken van een 50 Ω kunstweerstand (foto) of dummy load voor zelfs UHF is betrekkelijk eenvoudig als men de hand kan leggen op een "chip" weerstand.
https://pa0fri.home.xs4all.nl/Diversen/Dummyl/dummyload.htm

Oil Filled Dummy Load by AI4JI
This dummy load uses twenty non-inductive resistors in parallel to achieve fifty ohms over a very wide frequency range. The internal components are specially arranged and submerged in oil to dissipate heat and allow extended operation for transmitter tuning, testing and alignments.
https://www.nonstopsystems.com/radio/pdf-ant/antenna-dummy-article-1.pdf

QRP Dummy Load by N5ESE
This is another variation on the "parallel resistor" dummy load. This is one I built during my infatuation with copper pipe. It's perfect for QRP HF operation of 5-watts or less average power, and should be adequate for continuous operation at that level. It's light and compact, about 2-1/2" in length overall.
https://www.nonstopsystems.com/radio/pdf-ant/antenna-dummy-article-3.pdf


Creatie datum : 04/03/2019 @ 21:59
Laatste wijziging : 05/03/2019 @ 12:09
Categorie : Antenne-aanpassingen
Pagina gelezen 1058 keren


Print deze pagina Print deze pagina

Google Ads


^ Boven ^